#302 MVP Kwik-Cure Cordless UV Lamp

MVP KWIK-CURE LAMP FOR RESIN CURING

We’ve cut the cord and added a built in 45-second curing cycle with the powerful and compact MVP Kwik-Cure!

The MVP Kwik-Cure has six (6) 365nm UV LED diodes all housed in a durable
but lightweight aluminum case with four (4) suction cups for a strong
hold while curing.

The Kwik-Cure is built and assembled on-site at Liquid Resins, and each
lamp is tested and thoroughly inspected before leaving our facility. The
Kwik-Cure will deliver 2-3 hours of “on time” per charge and cuts the
cure time in half compared to our florescent-bulb curing lamps. The
Kwik-Cure will come with a standard USB cable for charging, a secondary
magnetic charging cable and a cigarette lighter adapter for charging on
the go.

The MVP Kwik-Cure’s LED diodes pulsate while charging. The lamp will take
approximately 4 hours to receive a full charge when starting with a low
battery. The Kwik-Cure’s LED diodes will turn solid when it is fully
charged and will no longer pulsate. This is how you will know you have a
fully charged curing lamp. The Kwik-Cure can be used while charging, but we recommend avoiding that if at all possible.

The MVP Kwik-Cure is best paired with Liquid Resins’ products. Our in-house
testing was done with our most popular resins (Green Cap, Red Cap,
White Cap & Super Hard Pit Resin). We recommend two 45-second cycles
while curing under pressure (top and bottom of the bridge &
injector assembly) and one cycle curing Super Hard Pit Resin. The Super
Hard Pit Resin will cure well before the Kwik-Cure completes its
45-second cycle.

The MVP Kwik-Cure comes with a 1-year warranty and an LED lifespan of over 150,000 repairs.

***Kwik-Cure Notes & Directions***

1. Remove
   the MVP Kwik-Cure from its box and inspect the lamp for any potential
   defects. Notify your Liquid Resins representative if you have any
   questions prior to use or while using the MVP Kwik-Cure.
2. The MVP Kwik-Cure is equipped with a built in 45-second timer when operating.
3. To arm the Kwik-Cure, push the black switch towards the red button. The red button is what activates the 45-second timer.
4. Press and hold the red button until the LED diodes pulsate 3 times. This means the Kwik-Cure is ready for its 45-second cycle.
5. After
   the lamp has flashed three times, push the red button again to initiate
   its 45-second cycle. You can push the button again for additional
   45-second cycles if needed. You can also cut a 45-second cycle short by
   pushing the red button while in use to temporarily turn off the lamp.
6. To
   disarm the Kwik-Cure, push and hold the red button until the LED diodes
   flash twice. You can also deactivate the lamp by pushing the black
   switch back to its off position, which is the side closest to the USB
   charging port.
7. Remember to avoid direct eye contact with the LED diodes and to wear protective eyewear.

What Others Are Saying About The MVP Kwik-Cure Lamp

“I have to say the lamp has exceeded my expectations
and was worth the wait. The size, ‘cutting the cord’ and going
wireless, and being able to cure in 30 seconds is a game changer, I truly can see why it’s called ‘MVP’ especially when time is money and you’re fighting daylight/UV. I love it! A second Kwik-Cure has been ordered!” -James Mills. Classic Enterprises Chip & Crack Windshield Repair

“My guys have been using the lamp non-stop ever since I gave it to them.
They were impressed at how fast it cured the repair compared to their
old curing lamp.” -Thomas Ledbetter. Quality Auto Glass.